强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

pusher hydraulic cylinder Sold to India

Release time:2023-11-12 11:05:37 Hits: Current position: Home > News

This article mainly introduces:

India hydraulic cylinder,pusher hydraulic cylinder manufacturer,pusher hydraulic cylinder

India pusher hydraulic cylinder

(India pusher hydraulic cylinder,produced by Hengyu Hydraulic Cylinder Factory)

pusher hydraulic cylinder are widely used in India,because of excellent fatigue and impact resistance,no need for deceleration device,long service life.So our company has designed pusher hydraulic cylinder for customers from India.

Introduction to pusher hydraulic cylinder:

pusher hydraulic cylinder hydraulic oil selection: The recommended working oil viscosity of the pusher hydraulic cylinder is 10 ~ 110cSt (1.8 ~ 15E), ISO VG46 hydraulic oil. The normal working oil temperature is 10 ~ 70℃, and the ambient temperature is in the range of -20 ~ 80℃. When the ambient temperature and service temperature are low, the hydraulic oil with lower viscosity can be selected.

If the pusher hydraulic cylinder operation failure, you can start from these aspects to troubleshoot: (1) the hydraulic system control pressure is too low. The throttling resistance in the control line may be too large, the flow valve is improperly adjusted, the control pressure is inappropriate, and the pressure source is disturbed. At this time, the control pressure source should be checked to ensure that the pressure is adjusted to the specified value of the system; (2) Air enters the hydraulic system. Mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced. (3) The initial action of the pusher hydraulic cylinder is slow. In the case of low temperature, the hydraulic oil viscosity is large, poor flow, resulting in slow pusher hydraulic cylinder action. The improvement method is to replace the hydraulic oil with better viscosity and temperature performance If the pusher hydraulic cylinder is weak and cannot push the load, please check the internal leakage problem. The internal leakage of the pusher hydraulic cylinder includes the leakage caused by excessive wear of the pusher hydraulic cylinder block seal, the piston rod and the seal cover seal and the piston seal. The cause of sealing leakage between the piston rod and the seal cover is that the seal is wrinkled, squeezed, torn, worn, aging, deterioration, deformation, etc., and a new seal should be replaced at this time. The main cause of excessive piston seal wear is improper adjustment of the speed control valve, resulting in excessive back pressure and improper seal installation or hydraulic oil contamination. The second is that foreign bodies enter the assembly and the quality of sealing materials is not good. The result is that the action is slow and weak, and in serious cases, it will cause damage to the piston and pusher hydraulic cylinder, and the phenomenon of "pulling the pusher hydraulic cylinder" appears. The treatment method is to adjust the speed control valve, and the necessary operations should be done according to the installation instructions.

If air enters the hydraulic system, the pusher hydraulic cylinder will not operate normally, mainly because there is a leak in the system. At this time, check the liquid level of the hydraulic tank, the seals and fittings on the oil suction side of the hydraulic pump, and whether the oil suction filter is too dirty. If so, the hydraulic oil should be replenished, seals and fittings should be treated, and the coarse filter element should be cleaned or replaced.

When the pusher hydraulic cylinder is in use, once the seal and guide support ring are found to be defective, the seal with the same structural form and appropriate material should be replaced according to the structural form of the pusher hydraulic cylinder seal to be repaired, so as to minimize the thickness of the oil film between the seal and the sealing surface and reduce the leakage of the seal.

Answers to some questions about pusher hydraulic cylinder:

What is the cause of the deep scratch of the cylinder?
The following reasons can cause the cylinder to be scratched. 1: Hydraulic oil containing particulate impurities into the hydraulic cylinder, these particulate impurities stuck between the piston rod and the guide ring (or stuck between the piston and the inner wall of the cylinder), when the piston movement in the cylinder will scratch the piston rod, the phenomenon of the inner wall of the cylinder, the more particles, the larger the scratch marks the deeper and more obvious. 2: The body of the cylinder itself. Due to assembly or design reasons, the coaxial error between the piston rod, piston, cylinder, guide ring and other parts is too large, or the cylinder, piston rod straightness error is too large, so that the piston rod and the guide ring interference between the cylinder, this mechanical interference will certainly lose the piston rod or cylinder wall.

What are the main dimensions of the cylinder?
The main dimensions of the cylinder include: cylinder inner diameter, piston cylinder diameter, cylinder length, cylinder wall thickness, stroke, installation distance, etc.

Back to list Recommended article

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP

强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

国产又粗又黄又刺激| 国产午夜福利在线视频| 日本女人性视频| 办公室扒开奶罩揉吮奶头的做法| 久久在线视频免费观看| 欧美噜噜久久久xxx成人高潮| 97影视大全免费追剧大全在线观看| 中文制服丝袜熟女av亚洲| 亚洲一区二区三区精品动漫| 国产精品乱码久久久久久 | 国产欧美又粗又猛又爽| 国产jizz| 国产精品偷拍| 热热热热热色| 天天综合网久久综合网| 国产人妖一区| 91人妻网| 亚洲人午夜射精| 中文字幕人妻在线一区| 亚洲激情偷拍| 日韩精品一区二区三区视频| 和漂亮岳做爰2| 99精品视频播放| wwwxvideos| 91精品国产入口| 97超碰中文| 人人妻人人爽人人| 国产精品偷伦精品视频| gogogo手机在线观看免费完整版| 国产亚洲黄色片| 白浆内射| 91精品国产福利在线观看| 国产毛片一区二区三区软件| 亚洲色成人WWW永久网站| 一本色道久久综合亚洲精品图片| 高傲人妻翘臀跪下好紧| YANDEX COM入口| 麻豆av在线观看| 性色av一区二区三区在线观看| 日本高清在线看| 射精视频在线观看|