强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

synchronous hydraulic cylinder Sold to Singapore

Release time:2023-11-08 15:23:32 Hits: Current position: Home > News

This article mainly introduces:

Singapore hydraulic cylinder,synchronous hydraulic cylinder manufacturer,synchronous hydraulic cylinder

Singapore synchronous hydraulic cylinder

(Singapore synchronous hydraulic cylinder,produced by Hengyu Group)

synchronous hydraulic cylinder are widely used in Singapore,because of simple structure and reliable operation,excellent temperature resistance,no transmission clearance.So our company has designed synchronous hydraulic cylinder for customers from Singapore.

Introduction to synchronous hydraulic cylinder:

Because of the slightly complex structure of the buffer synchronous hydraulic cylinder, sometimes there will be problems, such as when the synchronous hydraulic cylinder with the buffer device is started in reverse, the piston often stops temporarily or reverses. Elimination method: The orifice of the check valve is too small, so that the amount of oil entering the buffer chamber is too small, and even a vacuum occurs, so the above fault phenomenon will occur when the buffer plunger leaves the end cover. In this regard, the orifice of the check valve should be increased.

What kind of process is used in the synchronous hydraulic cylinder to make high-quality synchronous hydraulic cylinder products: the body is the main component of the synchronous hydraulic cylinder, mining single pillar, hydraulic support, gun tube and other products, and its processing quality directly affects the life and reliability of the entire product. Body processing requirements are high, the internal surface roughness requirements are Ra0.4 ~ 0.8&um, the coaxiality, wear resistance requirements are strict. The basic feature of body is deep hole processing, which has always troubled the processing personnel. The synchronous hydraulic cylinder products of our company mainly use rolling processing, because the surface layer has surface residual compressive stress, which helps to close the surface micro-cracks and hinder the expansion of erosion. Thus, the corrosion resistance of the surface can be improved, and the fatigue crack can be delayed or expanded, and the fatigue strength of the body can be improved. The correct rolling process of the synchronous hydraulic cylinder block: broaching block - fine boring block - grinding block. The rolling method is: broaching block - fine boring block - rolling block, the process is 3 parts, but the time is compared: grinding 1 meter of the block is about 1-2 days, rolling 1 meter of the block is about 10-30 minutes. Input comparison: grinding machine or quilting machine (tens of thousands - millions), rolling knife (ten thousand - tens of thousands). After rolling, the surface roughness of the hole decreases from RA3.2-6.3um before rolling to RA0.4-0.8&um, the surface hardness of the hole increases by about 30%, and the fatigue strength of the inner surface of the synchronous hydraulic cylinder increases by 25%. If the service life of the synchronous hydraulic cylinder is only considered, it is increased by 2 to 3 times, and the efficiency of the boring and rolling process is about 3 times higher than that of the grinding process. synchronous hydraulic cylinder misoperation or operation failure may be caused by the following reasons, you can start from these aspects of the investigation: (1) spool stuck or valve hole blocked. When the spool of the flow valve or direction valve is stuck or the valve hole is blocked, the synchronous hydraulic cylinder is prone to misoperation or operation failure. At this time, the contamination of the oil should be checked; Check whether dirt or colloidal deposits are stuck in the spool or blocking the valve hole; Check the wear of the valve body, clean and replace the system filter, clean the fuel tank, and replace the hydraulic medium. (2) The piston rod and synchronous hydraulic cylinder are stuck or the synchronous hydraulic cylinder is blocked. At this time, no matter how to manipulate, the synchronous hydraulic cylinder does not move or moves very little. At this time, check whether the piston and piston rod seal is too tight, whether it enters the dirt and gum deposits: whether the shaft line of the piston rod and the synchronous hydraulic cylinder is in the center, whether the wearing parts and seals are invalid, and whether the load is too large.

The piston rod of the synchronous hydraulic cylinder has two kinds of solid rod and hollow rod, and one end of the hollow piston rod needs to be set aside for welding and heat treatment. The solid piston rod material is 35, 45 steel, and the hollow piston rod material is 35, 45 seamless steel pipe. After rough machining, the piston rod is conditioned to 229~285HB in India, and if necessary, the hardness is 45~55HRC after high-frequency quenching.

The synchronous hydraulic cylinder body is commonly made of No. 20, 35, 45 seamless steel pipe, and the steel pipe is honed or rolled to achieve the roughness requirement within 0.4μm. The low pressure synchronous hydraulic cylinder can use 20 steel pipe, and the high pressure synchronous hydraulic cylinder can use 45 steel pipe.

Answers to some questions about synchronous hydraulic cylinder:

How to achieve hydraulic cylinder self-locking?
Hydraulic cylinder self-locking is divided into oil self-locking and mechanical self-locking. The oil self-locking is equipped with a valve to maintain pressure, so that the hydraulic oil of the cylinder does not return to the tank, and the oil chamber of the cylinder is filled with a certain pressure of oil. However, this pressure holding self-locking is not very safe and reliable, and the plunger will slowly return if there is a leak. Mechanical self-locking is to install a nut on the plunger of the cylinder, and when the cylinder rises to the required position, the nut on the cylinder plunger is rotated to the end, and the cylinder block is in contact, so that the plunger will be fixed to the required height. When it is necessary to relieve the pressure, screw the nut on again and let the plunger return to the position. This kind of cylinder has a special name, called self-locking hydraulic cylinder.

How to calculate the speed of cylinder weight decline?
To reduce the weight of the cylinder, the necessary condition is that the weight of the piston rod + external load is greater than the friction between the seal ring and the cylinder. There are many reasons for this, first of all, consider the reasons of the cylinder itself, the piston in the cylinder and the sealing ring on the piston rod will play a reaction force on the weight of the cylinder (because of friction), which depends on the tightness of the sealing ring and the cylinder. Secondly, what is connected under the piston rod of the cylinder and how much weight there is. And the way the cylinders are arranged, is it completely vertical. Anyway, in fact, the most important thing is to see how much the bore of the oil hole of the piston rod cavity of your cylinder is. For example, if the hole in the lower chamber of the cylinder is small, as thin as a needle, then its descent rate will be slow.

Back to list Recommended article

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP

强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

一本色道久久hezyo加勒比| 成人在线小视频| 婷婷久久丁香| 高h 肉 黄 乱 高| 久久综合狠狠| 欧美性生交xxxxx免费观看| 国产欧美日韩精品一区二区三区| 国产精品福利一区| 成人午夜视频免费看| 国产精九九网站| 日韩欧美亚洲一区二区三区| 白月梵星剧情介绍| 婷婷激情五月天基地 | 午夜福利理论片一区二区三区| 国产麻豆精品在线| 精品久久久中文字幕人妻| www.黄色在线观看| 精品人妻人人爽| 尤物视频在线观看| 亚州视频一区二区三区| 日本制服丝袜在线观看| 成人免费大片黄在线播放| 扒开腿添十八视频免费| 久久久久午夜| 少妇精品久久久久www| 国产视频一区二区在线观看| 久久精品视频中文字幕| 国产aⅴ爽av久久久久| 豆国产97在线 | 亚洲| 精品欧美一区二区精品久久久 | 性一交一乱一乱一视频出处 | 97视频福利| 韩国理伦片借种| 欧洲久久久久久| 精品中文字幕在线观看| 日本熟女在线观看| 日韩欧美在线一区| 精品国产乱码久久久久久108| 国产伦精品一区二区三| 67194少妇| 亚洲欧洲精品毛aa久久a就毛 |