强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

High quality hydraulic equipment manufacturers!
TELL:+8613184968882

servo cylinder Sold to Sweden

Release time:2023-12-12 10:13:40 Hits: Current position: Home > News

This article mainly introduces:

Sweden hydraulic cylinder,servo cylinder manufacturer,servo cylinder

Sweden servo cylinder

(Sweden servo cylinder,produced by Hengyu Hydraulic Cylinder Factory)

servo cylinder are widely used in Sweden,because of smooth movement,high work efficiency,excellent fatigue and impact resistance.So our company has designed servo cylinder for customers from Sweden.

Introduction to servo cylinder:

The viscosity of the working oil used in the servo cylinder is 29~74mm2/S, and ISO VG46 anti-wear hydraulic oil is recommended. Working oil temperature within the range of -20~80. C. When the ambient temperature and service temperature are low, the oil with lower viscosity can be selected.

The assembly work of the servo cylinder has a great impact on the quality of the servo cylinder: each part must be carefully cleaned before assembly; To correctly install the sealing device everywhere: when installing the sealing ring, pay attention to its installation direction to avoid oil leakage due to installation, and its lip should be equipped with a pressure oil chamber. In addition, because it is a YX-shaped sealing ring, it is necessary to pay attention to distinguish between shaft and hole use, do not install wrong; Because the sealing device is matched with the sliding surface, an appropriate amount of hydraulic oil should be applied during assembly; The special wrench should be used when the threaded coupling is tightened, and the torque should meet the standard requirements; After the piston and piston rod are assembled, it is necessary to measure whether the coaxiality and straightness on the full length are out of whack. After assembly, there should be no blocking sensation and uneven resistance when the piston assembly moves.

The repair method of servo cylinder wear: 1. Metal repair material is applied to the scratched surface; The first layer should be thin, uniform and fully covered with the scratched surface to ensure the best adhesion between the material and the metal surface, and then apply the material to the entire repair site and press repeatedly to ensure that the material is filled and reaches the required thickness, so that it is slightly higher than the surface of the guide rail; 2, the material at 24℃ to fully achieve the performance of 24 hours, in order to save time, can be through the tungsten halogen lamp to increase the temperature, the temperature rises 11℃, the curing time will be reduced by half, the best curing temperature 70℃; 3. After the material is cured, use a fine grinding stone or a scraper to repair and smooth the material higher than the surface of the guide rail, and the construction is completed.

When the piston speed of the servo cylinder is high, the steel ball of the check valve flows with the oil flow, so that the valve hole is blocked, and the servo cylinder moves irregularly. Elimination method: Replace the steel ball with a cone valve or spool with a guide shoulder.

Answers to some questions about servo cylinder:

What are the differences between hydraulic cylinder and pneumatic cylinder, what are their advantages and disadvantages?
Hydraulic Cylinder: small body and large force, constant speed and variable speed (easy to change), the adjustment of output is also convenient, and the degree of freedom of transmission is high. However, maintenance costs and installation costs are high, and there is the trouble of mild oil pollution. Pneumatic Cylinder: easy to control, low price, easy access to energy. But the force is small, and can not achieve the effect of stable speed. The gas-liquid pressurized cylinder has the advantages of both of the above: environmental protection and energy saving, easy control, and simple adjustment. However, the output of the trip has certain restrictions, so it is more suitable for short trips, large output, but also environmental protection and energy saving and low configuration of the occasion. Because the pressure used in the pneumatic system is generally in the range of 0.2-1.0Mpa, the cylinder is not suitable for high power component.

How to remove the cylinder correctly?
(1) Before disassembling the hydraulic cylinder, the hydraulic circuit should be depressurized. Otherwise, when the tubing joint connected with the cylinder is loosened, the high-pressure oil in the circuit will be quickly ejected. The hydraulic circuit of the hydraulic press should first loosen the hand wheel or pressure regulator screw at the relief valve, so that the pressure oil is unloaded, and then block the power supply or block the power source to stop the operation of the hydraulic equipment. (2) When disassembling, it should prevent damage to the top thread of the piston rod, the oil thread, the appearance of the piston rod, the inner wall of the cylinder liner, etc. In order to prevent the piston rod and other slender parts from twisting or deformation, the use of cushion wood support balance when placed. (3) Disassemble in order.

Back to list Recommended article

Send
Email

Email:hsslrubbertech@gmail.com7x24 hours

Glad to receive your consultation!:

Service
Tel

+8613184968882
7x24hours service

Add
Wechat

Add Wechat
TOP

强伦人妻一区二区三区视频18|自拍偷在线精品自拍偷无码专区|精品人妻久久久久久888不卡|色婷婷中文字幕

大地资源高清在线视频| 妃子露出两个奶球让皇帝吃奶头| 少妇被猛烈进入的片90分钟| 亚洲欧美一区二区在线观看| 天天日天天干天天操| 国产成人欧美一区二区三区八| 欧美成人高清在线| 日韩人妻一区二区三区蜜桃视频| 久久久噜噜噜久久| 高清国产av| 久久精品熟女| 中文字幕乱码天天综合| 屁屁影院网站导航| 亚洲熟妇xx| 国内精品久久久久久| av网站在线免费| 91久久精品无嫩草影院| 国产麻豆久久久| 国产精品午夜影院| 中文字幕午夜福利| 三年片免费观看大全国语第二季 | 国产精品扒开腿爽爽爽的视频动漫| 日韩成人在线播放| 久久久99国产精品免费| 中文字幕免费看| 亚洲中文字幕无线| 中文字幕电影一区二区| 亚洲精品无码久久| 又粗又长又硬又大又爽α片| 久久久人妻视频| 内射无码专区久久亚洲| 色婷婷18禁| 精品人妻一区| 久久久久久久久久逼| 国产91福利在线观看| а√新版天堂资源中文| 1024精品久久久久久久久| gogogo高清在线观看免费播放| 日韩精品在线免费视频| 9久久婷婷国产综合精品性色| 永久av在线|